PS Tools Mini Lathe

The PS Tools Variable Speed Mini Lathe, from Pop’s Shed doesn’t make for too bad a starting point for a new turner, both with the convenience of variable speed, as well as the accessories that Pop’s Shed bundle with it.  The price is $695 (including around $100 worth of chisels, a $75 keyless Jacob’s Chuck, and about $125 worth of mini lathe chuck) which brings the lathe itself down to around $400 in value.  The Jet VS is around $675 without accessories fwiw, and doesn’t include the speed readout.

With Pen Blank, Ready for Turning

The lathe uses the standard #2 morse taper for mounting tools, which makes it easy to upgrade or add other live centres, drive spurs, drill chucks etc and has a threaded section on the drive shaft for various jaw chucks.   The head speed indicator was a particularly interesting inclusion, something that isn’t on the VS Jet, and although not essential, as Nova Lathe users will probably testify it is useful getting accurate speed readings, at least in some circumstances.  I certainly liked being able to dial-in a specific speed, and found myself wishing I had a variable speed unit on my Jet lathe.

Mini Chuck

The mini-chuck is a smaller version of a standard self-centering chuck, and it comes with 4 different jaw sets, as well as a mounting plate (used by screwing directly to the timber for odd shapes etc that cannot be otherwise mounted on the lathe).

Mini Chuck Accessories

If compared to a full-sized chuck (such as the Nova G3) and the equivalent jaw sets, it is quite a saving although with considerable less capacity.  However, on a mini-lathe it at least ensures you are not tempted to grossly exceed the lathe’s capabilities.

Keyless Jacobs Chuck

The keyless Jacob’s Chuck was actually rather interesting.  Without getting inside it to see about the quality of the build, it seemed to operate smoothly, and the jaws closed down to pretty much zero clearance (allowing the smallest of drill bits to be mounted).  Drilling on a lathe has a fundamental difference to drilling on the drill press.  Instead of the chuck revolving with the drill bit, it is (rotationally) stationary, and instead the workpiece revolves.  The drill bit is wound into the revolving workpiece via the tail stock thread.

On this lathe (and sadly with a number of threaded tools coming out of China), they don’t seem to be able to make a really smooth operating thread.  I may at some stage see if I can get the tail stock apart and see if the thread can be cleaned up so it operates smoother.  It works as is, but there is working, and then working well.

Speed Sensor Wheel

Inside the headstock there is this toothed wheel next to the belt drives.  The belts still have 3 pulleys, so the variable speed can be set to one of three speed ranges, covering a total speed range of around 600RPm to 3000RPM.  The method for determining speed is the same as old (ie non laser/optical) computer mice, using a light transmitter/receiver shining through a toothed wheel and the rate the light is strobed is used to calculate head speed.

Beginner Tool Set

The chisel set has the more popular chisel types (bowl gouge, roughing gouge, skew, parting tool, scraper, spindle gouge), and will get you started.  As your skills develop, you’ll want to start replacing the chisels you most commonly use with better quality (ie expensive) ones, but having a basic set such as this will at least give you a feel for the different types, and plenty of sharpening practice without doing so on an expensive chisel.  (Given the entire set is worth around $100, and a decent chisel costs about that individually, I’m not being unreasonably harsh).  This set will get you started on the journey (and trust me, wood turning is a slippery slope!)

In checking the lathe itself, I started by turning the fire-pen from Rockler, and it went smoothly until I got down to near the end.  I found the pen was slightly off-centre, but I am putting that down to user error – I hadn’t mounted the pen spindle as central as I needed to, because when I checked the alignment of the head and tail stock, I couldn’t see any problem there.

Head Stock / Tail Stock alignment

Checking how the head drive spur and live centre in the tail stock line up is one of the fundamental checks if a lathe is made properly, and the PS Tools lathe had no issues there, as you can see from the above-photo.

I’ve had some off-line comments sent through about another brand that looked very similar to this lathe, and I will keep an eye on those pickup points, but at this stage I haven’t experienced any of the problems mentioned, and it may just be a case of similar models/brands, but not the same.

Pop’s Shed Lathe

PS Lathe

With all the (non shed related) happenings this week, I haven’t been able to commission the PS Tools lathe yet, but hope to rectify that shortly.  I did get to plug it in and push the on button!

I could really become a fan of variable speed lathes – the ease of changing speeds (without having to change belts) is really refreshing.  The speed readout is also not based on the controller, but the actual speed of the shaft.  This means that if turning a larger item (or placing more load on it with aggressive cuts), the speed readout reflects the actual RPM being achieved.  It does this with a toothed wheel inside the lathe head mounted directly to the shaft, and a light sensor circuit that counts and times each tooth.  The same principle was used in computer mice pre optical and laser days.

The lathe still has 3 belts, so you can get 3 ranges of variable speeds, from the slowest around 650RPM right up to 3000RPM.

Sitting on top of the Torque Workcentre is not it’s usual position (too high), but the juxtaposition is deliberate even so.  I have an idea about using the lathe, with the overhead router for turning helices, and also for cutting evenly positioned flutes.

Something to mull over.  In the meantime, I will get to a better introduction to the lathe, and all the accessories it comes with shortly.

A Pop out to view a Shed

that is.  A brand new business that just started out at Chirnside Park, Lilydale (northeast Melbourne).

Unit 10B
Rear of 286 to 288 Maroondah Highway
Chirnside Park

03 9727 0611

It has been open a whole 2 1/2 weeks, so very new!

As you pull up to the door (behind the shopping centre next to the Bunnings), the first thing you see is the timber – boxes of burls, Banksia nuts, and a wall of turning blanks – you KNOW you are at the right place!

Pop's Shed

Next door is Toodlebug Toys, so it can be a family outing (if you have younger kids!)

Timber Collection

There are lots and lots of sorted timber burls to pick and choose from,

More Timber

Banksia Nuts, slabbed burls and

Turning Blanks

a wall of turning blanks

Turning Tools, Pen Blanks & Consumables

They stock a range of pen hardware and associated turning tools and accessories, with a collection of pen blanks – mostly timber with a few acrylics.

Mini Lathe & Linisher

The company sell a few shop machines as well – a mini lathe, a maxi lathe, a linisher, bandsaw and drill press. All the things you’d need if getting started in turning. The mini lathe kit will get a closer look in another article shortly – variable electronically controlled speed, and comes with a mini chuck, drill chuck and a set of turning tools.  Now if you know nothing about turning, this is very much what Pop’s Shed has been to cater for – both getting you started, as well as keeping you supplied!  To get started though, nothing beats hands-on instruction, and at the back of the store, just behind the wood stove (failed project disposal unit) and where a Chesterfield couch and Flat screen TV will be going shortly, is the training room.  While you are wandering around the shop area, you can see what is going on inside the room through glass windows which is a nice element – keeping the noise and dust out of the sales area, but not separating the two completely.

Training Area

There are a number of maxi lathes in there to learn on, but what caught my eye (and some astute readers will have already seen it as well) – a very familiar colour…

Training Room

A Triton Mk3 has found its way in, for preparing timbers for turning!  There are 4 maxi lathes, one mini, a bandsaw, drillpress, and linisher, and each station has dust & chip collection dedicated to each machine, all professionally plumbed in (I could learn some lessons from how neat this job has been done!)

Dust Collectors

Behind the training room, there is the dust collection room, with 4 x 2HP dust collectors. As you can see, it is all brand new, just waiting for the courses to be arranged and begun, and I’ll publish here what courses they have once they are up and running.  So if you were curious about wood turning, or wanted to improve your skills, have a chat to one of the Pops (or Pops-to-be (grandfathers) as it happens!) Brian, who is there full time, or Chris.

I’m particularly impressed with the training focus they have taken, and it is becoming a very nice little setup they have there. Pop in to Pop’s Shed if you are passing by 🙂

(PS, any similarity in the name is purely coincidental!)

%d bloggers like this: