End of Days: The Pandora box is complete

And so we have arrived at the point where the box is revealed as fully formed, closed and opened. Not a pithos as was originally written in Greek by Hesiod in “Works and Days”, but the Latin “pyxis” as the original myth was mistranslated back in the 16th century.

Trays lined with felt

I had to be really patient to get to this point – lining a box (when it is done) really shows the box and how it will finally look, and this was no exception.  The bottom and inside of the main box was lined in black (as a point of difference from the ‘working’ surfaces.  I didn’t need to do the inside, but it gives a sense of completeness if both trays are ever lifted out.  Getting the lower tray out is tricky in any case – there is a bit of a vacuum effect there (not a lot, but enough to be noticeable – the benefit of a close fit).

I chose a royal blue for the two trays – giving consideration to how the jewellery will stand out on such a colour.

Dividers in place

Next, the dividers were added.  These are only a friction fit – they are not glued in.

Trays in location

Coming together.  the upper tray slides back and forth revealing the lower compartments.   It can also be easily lifted out as required.

Lid attached, and charms, bracelets and necklace added

Finally, the lid has the hinges added, and they all slide together.  Getting the hinges into the lid was a bit nerve-wracking.  It is burl after all – not the strongest of materials, and each hinge had to be carefully tapped into location.  Once all three were attached, the hinges were lined up with the holes in the box, and carefully pushed together.

It is shown here without a lid restraint  that I have since added (to stop the lid being opened too far), using a black leather cord and some fittings from jewellery-making added so it can be screwed to a small hole drilled into the top and the side wall of the box (inside).

Concealed hinge detail

Bit of a closeup of the hinges in action.  They are not the strongest hinge, but are very clever in mechanism, and fully concealed when the lid is closed.

Lid detail

A bit of a closeup of the lid beading.  Making it out of the same timber as the top worked out really well, and it has machined nicely on the router table.  The slight apparent overhang of the mitre joint is actually an illusion – it isn’t there to see or feel in reality- trick of light, or shadow.  Beautiful features in the timber – burls can be really stunning.

So finally, the last one – the completed box.  Probably should have taken another from the side – may post it here later.

Completed Pandora Box

I’m certainly happy with how it has come out, and surprisingly, the recipient didn’t have a clue.  I thought I was gone for all money, that she suspected I was up to something, but I got away with this being a complete surprise.  The best kind!

 

 

Opening Pandora’s Box

I always seem to leave my run very late, but seeminly managed to kick off a project this weekend just in time. My wife tends not to read this blog, so if you happen to do so, and also know her, best to not mention this post at all!

With her 40th approaching (in a couple of weeks), I’m wanting to make a bit of a jewellery box that is specifically designed for her collection of Pandora bracelets, necklace and spare charms.

It is getting designed as I build it, so I don’t know what the final item will look like yet- each step reveals a little more detail.

To start, I’ve taken a length of Silky Oak off the woodrack. It was really twisted, so rather waste a huge amount of the timber trying to get it flat, it was easier to rip it down the middle.This worked out ok anyway, as the resulting boards were about the height of the sides I envisaged I’d need. These were run through the jointer/planer to get one flat side, then using that side as a reference, run through some more passes to get an edge at 90o to that side.

From there to the thicknesser, running both boards through to ensure a uniform thickness, then finally back to the tablesaw to set the final box side height, then docking the boards to length.

20120708-014255.jpg

Next, it was over to the router table, where once again I utilised the Gifkins dovetail jig to create the joints I wanted. As always, it didn’t take long, and the resulting dovetails were perfect.

20120708-014450.jpg

Changing over to a small slot cutting router bit (one with a bearing, limiting the depth of cut to 5mm), and temporarily assembling the sides with clamps to hold the box together, a groove was cut all around the inside of the box, about 5mm up from the bottom.

Instead of wasting another piece of Silky Oak, (especially considering I am planning on covering both sides with felt), I took a piece of crapiata (Pine), and cut a base for the box, 10mm larger in each dimension than the inside dimensions of the box.

Back to the router table, and a groove was cut all round (also 5mm deep) to create the lip that will fit the groove in the box sides. Over to the thicknesser, and the extra thickness was removed leaving a board around 10mm thick, so that when it is in the slot of the box sides, it is flush with the bottom.

20120708-015217.jpg

Later on in the build, I will cover this with some felt.

Turning the box upside down and pulling off one side, you can see how the base engages with the box side. The sides are then glued together, leaving the base unglued but captive.

20120708-015509.jpg

My final job for the day was to experiment a bit with the dividers that will be used to separate each of the bracelets, and create cells for each of the loose charms. I will create two trays that fit inside the box, each with a different arrangement of dividers. To get the dividers, I took a block of jarrah, and cut it into thin strips, about 2.5mm thick on the bandsaw.

20120708-015855.jpg

It was only a small block to start with, but that is the benefit of the bandsaw- resawing, and a very thin blade kerf wasting a minimum of timber.

20120708-020023.jpg

Using my recently-created thin stock carrier for the drum sander, the strips were passed through to get them to a required finish and uniform thickness. I wanted to cut slots using a thin-kerf tablesaw blade, so sized the strips down to match that.

20120708-025019.jpg

Ripped once more to the final desired height, that one small piece of jarrah yielded a fair collection of dividers!

20120708-025140.jpg

There wasn’t enough time to do much more, other than a quick test of the dividers.

20120708-025238.jpg

Next time, I will create a couple of trays, fit the dividers in, and sort out the lid and hinges.

At least I have made a start!

The Box Progresses

Glueup complete, now just needs to be sanded, have the lid fitted, oiled, waxed, felt applied, and inserts constructed.  Hmm wonder if Xmas will beat me?

Mulga and Cyprus Box

Mulga and Cyprus Box

Still need the large and small trays for the various Pandora paraphernalia.  (Chains and individual charms)

%d bloggers like this: